Fender Twin Reverb II

Model/Circuit Number:
Years of Production:
1983 – 1986
Era:
Configuration: Combo, Head
Controls: Black, forward facing w/ white labels
Knobs: Black skirted w/ chrome center, numbered 1 – 10

Schematics

Faceplate

  • Front: In 1, In 2, Vol (Pull for Bright), Treb, Mid, Bass – Vol (Pull for Ch Select), Gain, Master Vol, Treb, Mid (Pull for Boost), Bass, Reverb, Presense – Standby Sw, Power Sw, Pilot Lamp
  • Rear: Fuse (4A), AC Outlet (Grounded, Polarized), Ground Sw (A/Off/B), Speaker (1/4”), Ex Speaker (1/4”), Line/Recording (1/4”), Output Matching, Return Level, Return (1/4”), Send (1/4”), Send Level, Reverb Out (RCA), Reverb In (RCA), Pedal Plain (1/4”), Pedal Red (1/4”), Hum Balance

Cabinet

Covering Material

Logo: Grill mounted, raised, chrome & black script
Weight: Twin Reverb II: 75 lbs. ; Twin Reverb II Top: 45 lbs.
Speaker

Effects: Reverb, Channel Switching
~Watts: 105 watts
Tubes

  • Pre amp: 7025
  • Power: 4 x 6L6

Bias: Fixed
Rectifier: Solid State

Comments: Cabs available for Twin Reverb II Top were (all open back w/ standard hardware): 1-12 OB: 23 5/8″w x 16 1/2″h x 11 3/8″d, 8 Ohms, 27 lbs, 100 Watts Max 1-12 OB Deluxe (EV Speakers): 23 5/8″w x 16 1/2″h x 11 3/8″d, 8 Ohms, 32 lbs, 200 Wats Max 2-10 OB: 23 5/8″w x 16 1/2″h x 11 3/8″d, 8 Ohms, 30 lbs, 150 Wats Max 2-10 OB Deluxe (EV Speakers): 23 5/8″w x 16 1/2″h x 11 3/8″d, 8 Ohms, 35 lbs, 300 Wats Max 4-10 OB: 23 5/8″w x 24 1/4″h x 11 3/8″d, 8 Ohms, 53 lbs, 300 Wats Max, recessed side handles 2-12 OB: 26 1/4″w x 16 1/2″h x 11 3/8″d, 8 Ohms, 35 lbs, 200 Wats Max 2-12 OB Deluxe (EV Speakers): 26 1/4″w x 16 1/2″h x 11 3/8″d, 8 Ohms, 42 lbs, 400 Wats Max 4-12 OB: 26 1/4″w x 28″h x 11 3/8″d, 8 Ohms, 59 lbs, 300 Wats Max, recessed side handles

6 thoughts on “Fender Twin Reverb II

  • September 7, 2013 at 9:52 am
    Permalink

    Where can I get 2 t630ma fuse holders for this amp,can anyone help me ?

    Reply
  • October 24, 2018 at 6:41 am
    Permalink

    Hi guys can I connect the TWin reverb 2 to 1 single external C12n Jensen speaker (50 Watt 8 ohm)?

    Thank You

    Luca

    Reply
  • January 23, 2019 at 6:22 am
    Permalink

    Hi Guys,
    I was hoping to try the remove two power tubes and one speaker mod on the Fender Twin Reverb II like many have tried on the original Twin Reverb amp.

    Will this work on the Twin Reverb II? Is it safe for the amp? Was hoping for some feedback.

    Thanks,
    Jim

    Reply
    • April 25, 2019 at 8:59 am
      Permalink

      Hi Jim,

      I’m no expert, but I have the same amp and my youngest son knocked it over and broke two power tubes. So I disconnected a speaker and put the two tubes in the centers. You can do both in the centers or both in the outers, but don’t mix them.

      Reply
  • January 31, 2021 at 6:25 am
    Permalink

    yes like justin said you could do it if you use the socket for double the real value of the speaker ( 8ohm speaker ,plugged into 16ohm socket ). i think you might be able use valves 1 and 3 or 2 and 4 as well ,just not both left or both right.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *