Fender Silverface Bassman 10

Model/Circuit Number:
Years of Production:
1972 – 1982
Era: Silverface
Configuration: Combo
Controls: Silver forward facing w/ blue labels
Knobs: Black skirted w/ chrome center, numbered 1 – 10

Faceplate:

  • Front: Bass In, Normal In, Deep Sw, Vol, Treb, Bass – Bass In, Studio In, Bright Sw, Vol, Treb, Mid, Bass – Master Volume – Pilot Lamp
  • Rear: Ground Sw, Fuse, Power Sw, Standby Sw, Speaker Jack

Cabinet:

Tolex/Tweed:

Grill Cloth:

Logo: (68-74) Grill mounted, raised, chrome and black script with tail
Weight: 75 lbs
Speaker:

Effects:
Watts: 50 watts ~ 1972-1976, 75 watts ~ 1977-1982
Tubes:

  • Pre amp: 2 x 7025 ; 12AT7
  • Power: 2 x 6L6GC
  • Bias: Fixed
  • Rectifier: Solid State

Comments:
Some later Bassman 10’s had a MID control on the bass channel. Bassman 10’s produced between late 1980 and 1982 have a black control panel and Black White Silver grill cloth. Output increased to 70 watts when CBS switched to an ultra-linear output transformer.

67 thoughts on “Fender Silverface Bassman 10

  • June 26, 2011 at 4:25 pm
    Permalink

    what are these amps worth

    Reply
    • June 26, 2011 at 5:24 pm
      Permalink

      On the previous version of ampwares there was a module that queries ebay results and posted an average of the ending prices. The service that maintained the module stopped in may. I will be working in the near future to build a similar module for this version of the site.

      Reply
    • August 18, 2019 at 10:33 am
      Permalink

      Whatever you can get

      Reply
    • April 17, 2020 at 7:55 am
      Permalink

      Recently purchase one for my 16 year old. I would say these amps are priceless! Somewhat more seriously, they are going to be pick up only. At 75 pounds they don’t travel too far. Amazing sound, lot of fun. If you don’t like it or get tired, they hold their value and you can likely sell it for what you paid.

      Reply
  • July 19, 2011 at 5:51 am
    Permalink

    FYI
    The 4-10″ speakers are 32 Ohm

    Reply
  • July 20, 2011 at 4:18 pm
    Permalink

    Actually, the final impedance for those amplifiers is 8 ohms total.  (4) 32 ohm speakers wired in parallel for a total 8 ohm load.

    Reply
  • August 30, 2011 at 1:31 am
    Permalink

    just had one restored by a reputable shop last winter and am loving it as a decent bass amp, a fair guitar amp (lacks break up that I desire in a tube circuit but makes up for it in power for low end crunchiness) and even as a surprisingly toney piano amp. Wish I had a Rhodes, the Roland sounds GREAT through it.

    Reply
    • December 2, 2011 at 7:14 am
      Permalink

      If it was restored the tubes were replaced with equivalent of the originals, if you replace the first tube (V1) with a chinese made 12AX7 and move he original 12AX7 to the 12AT7 socket you will get more break-up, but the Chinese tubes won`t last as long

      Reply
    • June 10, 2021 at 1:05 pm
      Permalink

      You can correct this in one kf two ways (or both if you need more gain than everyone on the planet:

      1. Replace the 12ay7 pre amp tube with a 12ax7. (EHX is my recomendation).

      2. Use an overdrive or distortion pedal between guitar and amp input jack with bright switch on. I put an EHX (no, i dont work for ehx) soul food drive on mine which is a klon centaur clone and the tone was ax rock n roll as it gets!! Have several at your command, klon clones, tube screamer, fuzz face, bk butler, mxr distortion+, ehx big muff, etc…. .

      The B10 is a killer tuba amp platform for modding.

      Reply
      • June 10, 2021 at 1:13 pm
        Permalink

        Ooops, i meant switch out the 12ay7 with a12ax7 not a12at7.

        Reply
  • September 10, 2011 at 4:25 pm
    Permalink

    Hi all,
      I’m looking for a replacement face plate and treble pod for the  (1st channel bass) for my early 70’s bassman 10.  Email AL
    althedj@gmail.com

    Reply
  • November 18, 2012 at 8:30 am
    Permalink

    I have a Bassman 10 that I bought new in 1972. It still works great and I’ve never had a problem with it. Everything is still original, never had to change a tube or anything. Could anyone tell me what it’s worth now?

    Reply
    • August 22, 2014 at 8:35 am
      Permalink

      Being the original owner and if you kept it in good condition. You have approx. $850.00 value.
      $500 fair condition and $300 poor condition.

      Reply
      • October 30, 2018 at 11:44 am
        Permalink

        I could give ya a couple hundred that is if you deliver…..don’t get mad, just kiddin’

        Reply
  • February 13, 2013 at 9:37 pm
    Permalink

    Looking for a road case for one of these…anyone help?

    Reply
    • February 14, 2013 at 9:15 am
      Permalink

      Try e-mailing Lopoline.

      Reply
      • February 15, 2013 at 2:40 pm
        Permalink

        They build cases too? You have any experience with quality/price with them?
        Thanks for the info

        Reply
  • March 2, 2013 at 6:54 am
    Permalink

    i am looking for a fender bassman 10 owners manual to download? thank you, bob

    Reply
  • September 12, 2013 at 4:08 am
    Permalink

    I recently bought a 79 bassman ten, and its been blowing fuses like crazy. Any word of advice?

    Reply
    • April 19, 2014 at 2:05 am
      Permalink

      Hi, Probably faulty power amp tubes. Can have intermittent short. Changing it may be the cure. If not, the amp is good for a professional check/overhaul… Pretty basic advice indeed, but i hope it will help.

      Reply
  • October 23, 2013 at 6:57 pm
    Permalink

    Does anybody know if Fender produced in the past years a “head” version of the “Ten” Silverface ??
    I’m asking ‘cose there’s one here where I live, and I couldnt find any info in the .net about it. Everything look original. Its owner says its been made in early 70’s (1972). However I’m now tryin’ to find help in here. I have the budget, but … is it a real “Ten” head ??
    I would apreciate any advice. Thanks

    Reply
    • December 5, 2020 at 4:16 am
      Permalink

      The Ten was always a combo as far as I know. A head would be a cut down version.

      Reply
  • February 26, 2014 at 10:45 am
    Permalink

    amps made between 1977-82 are 4 ohm – four 10” speakers are 16 ohm wired in series

    Reply
  • May 28, 2014 at 9:05 am
    Permalink

    I am looking for a new blackface faceplate for a bassman 10 Dwight

    Reply
    • June 13, 2015 at 8:40 am
      Permalink

      I need one of those black face plates as well…did you ever find a place to get them? Thanks…Mike

      Reply
  • September 26, 2014 at 2:29 pm
    Permalink

    I acquired a bassman 10 ,4×70 amp. the guy I got it from had cut the top off the amp, and tried or actually made a two piece amp. In other words, he tried to make a head with a 4×10 cabnet. I want to put it back the way it was. Where can I find a cabnet? please help…….

    Reply
    • November 2, 2014 at 4:57 am
      Permalink

      Chris, I just acquired a bassman 10 cabinet in a trade this week. It will need your back panel, since someone in the past has remover the electronic from it, and closed the back with plywood. I will keep speakers and sell the cab. If you are interest, let me know asap.

      Reply
      • October 5, 2015 at 3:55 am
        Permalink

        Jerry do you still have the Bassman 10 Cab?

        Reply
    • April 8, 2020 at 4:35 pm
      Permalink

      A Fender Super Reverb seems to be the same dimensions.
      I’ve seen used cabs on EBay and new from places like Mojo

      Reply
  • January 9, 2015 at 7:49 pm
    Permalink

    Recently bought a fender baseman 10, and as well as getting it serviced I wanted to buy a little stockpile of tubes and stuff so I’m ready to replace them when they blow. But I also want to buy spare fuses, and I’m not sure the exact type of fuse to use for this amp, can anyone help me? Or know what fuses to buy? Thanks.

    Reply
    • May 5, 2015 at 9:47 pm
      Permalink

      The Bassman 10 uses a 2-1/2 Amp, Slo-Blo fuse. It’s silkscreened on the back panel above the fuse holder. Party on!

      Reply
  • January 23, 2015 at 8:22 am
    Permalink

    I have the mate of this amp wanting to sell as its in mint condition not used for 30 years, still works well has been tested this past week

    Reply
    • March 11, 2015 at 4:35 am
      Permalink

      Hi, what country are you in Bud?

      Reply
  • March 22, 2015 at 10:26 am
    Permalink

    Hello, I have a mid- 70’s Bassman Ten and would anyone know what the Potentiometer under the chassis and the pot on the far right of the rear panel adjust? The pots have no knobs, you have to use a straight blade screwdriver to move them.

    Thanks in advance.

    Reply
    • June 8, 2015 at 4:15 am
      Permalink

      The pots on the back are Bias / Hum balance adjustments

      Reply
    • June 20, 2015 at 5:47 am
      Permalink

      Hi Asa, those pots are for balancing the bias. Only for use by an amp technician. Don’t adjust them.

      Reply
    • April 8, 2020 at 6:06 pm
      Permalink

      I believe that is the bias adjust ment pot

      Reply
  • July 25, 2015 at 7:23 am
    Permalink

    I just picked up Bassman Ten from a guy moving out of state. Thank Jebus, Amen and all that. Wow, what a killer, affordable, versatile vintage Fender tube amp. I notice the stamped #’s on the rear, right hand side of the chassis (facing the amp) A58875. Does this translate to 1975 ?

    Reply
  • August 15, 2015 at 5:02 am
    Permalink

    I have an early 70’s silverface Fender Bassman amp in fair to exellent condition.. make of offer ( shipping is on you )

    Reply
    • July 9, 2016 at 10:05 pm
      Permalink

      Hey what’s up. Still have your bassman 10? 500$?

      Reply
  • November 6, 2015 at 9:59 am
    Permalink

    I have a 78 Bassman Ten, Silverface s# starts with A8…
    I have 4 (dials) volume, treble, midddle for BOTH (bass/instr) and the (normal) channels.
    Can someone explain why this is? Most only have 3 dials on the (bass instr) side…

    Thanks,
    Bp

    Reply
  • November 6, 2015 at 10:01 am
    Permalink

    DOH!
    I have a 78 Bassman Ten, Silverface s# starts with A8…
    I have 4 (dials) volume, treble, midddle, bass for BOTH (bass/instr) and the (normal) channels.
    Can someone explain why this is? Most only have 3 dials on the (bass instr) side…

    Reply
  • April 21, 2016 at 4:01 pm
    Permalink

    Does anybody know where to find a protective bag like case for this amp?

    Reply
  • June 4, 2016 at 2:34 pm
    Permalink

    Thanks for finally writing about > Fender Silverface Bassman 10 | Ampwares < Loved it!

    Reply
  • October 8, 2016 at 10:53 pm
    Permalink

    I have a 1976 model and I need a replacement pilot bulb – what is the bulb specs please. I think it is a screw in ?

    Reply
    • December 14, 2018 at 4:54 pm
      Permalink

      GE 49 or Sylvania 755. It is a 6.3 volt bulb.
      bayonet mount

      Reply
  • December 9, 2016 at 9:56 pm
    Permalink

    I have one of these babies serial number A 000344. can any one confirm the year. I need to know where to get tolex for it as well all help is appreaciated.

    Reply
  • December 9, 2016 at 9:57 pm
    Permalink

    corrected serial number A 00344.

    Reply
  • December 27, 2016 at 11:01 pm
    Permalink

    FWIW there are several errors and unanswered questions in earlier comments.

    The (roughly) 50 watt silverface version of the Bassman 10 had four 32-ohm speakers wired in parallel for an 8-ohm load. The output transformer will handle a 4-ohm load, but it will result in slightly less power due to the impedance mismatch. It may be imperceptible, and with some preamp mods may work that way as a guitar amp (much less so as a bass amp except as a low-volume studio amp)

    The ’77-80 silverface and ’81/82 blackface amps use an ultra linear output transformer, hitting the tubes with much higher plate voltages and pumping out up to 70 watts. These models use different speakers – 16 ohm speakers wired in parallel (NOT series as noted earlier – that would result in a 64 ohm load and an extreme load on the output transformer) for a 4-ohm load. This is unlike the Super Reverb, which uses 8 ohm speakers for a 2-ohm load. The ultralinear circuit also has one less tone control on the bass channel.

    From ’72-’76 Fender also produced the Bassman 50 head (50 watts), and the Bassman 70 head until the end of the run.

    Reply
  • January 11, 2017 at 8:26 am
    Permalink

    I have a fender bassman 70 head, and was wondering if anyone knows what cabinet was originally matched. Td

    Reply
  • January 23, 2017 at 3:02 am
    Permalink

    Have anyone tried to install 19″ tilt back legs on Bassman Ten ? Will it fit?

    Reply
  • August 19, 2017 at 4:19 am
    Permalink

    I just got one of these great amps! I found it at a GC a couple of weeks ago looking very used, with ripped tolex and marks all around the normal and bass #1 inputs. Someone tried to replace the grill cloth but didn’t get it tight enough. It looked very rough as only an amp that has seen a lot of use can look. I loved the sound but didn’t pull the trigger right away. It wasn’t long until I realized that I just couldn’t get it out of my mind. I had to have it. So I finally went and bought it.

    When I got it home, I thought that I would like to clean it up a little, but retain it’s awesome “patina.” I took everything apart, just leaving the speakers in the cabinet. I love seeing that hand wired, point to point electronics. 🙂 One weird thing is that the power switch is 180 degrees out. You have to turn it to “off” to turn it on. I wanted to see if I could easily flip that switch (while I had access to the inside). I found that there’s a groove cut in the threads (of the switch) that lines up with a point on the face plate. So it was obviously originally built this way. Strange! I left it alone. All I did was wash forty years of dirt and smoke off of it. I also ripped off any long flaps of streaming tolex (knowing that they would only further pull at surrounding tolex). I also re-did the new grill cloth nice and tight/straight. I put it all back together and it looks a lot better.

    What can I say? I absolutely love it!

    Reply
  • February 12, 2018 at 7:20 pm
    Permalink

    What amp circuit is the 1978 Fender Bassman Ten 4×10 combo? I want to blackface / “Marshallize” it, but I want to make sure I start with the right schematic. Anyone know of a schematic to add a third 12AX7?

    Reply
  • April 15, 2018 at 1:39 pm
    Permalink

    I have a Bassman Ten can with original speakers for sale, if someone is looking for one.

    The amp is not included as I have installed it in a new Mojotone super reverb cab.

    Reply
    • January 15, 2019 at 6:56 pm
      Permalink

      Do you still have the bassman ten cabinet and speakers?
      Condition? Price? Location?

      Reply
      • March 12, 2019 at 3:46 am
        Permalink

        Alan,
        Are you still looking for a cabinet for a Bassman Ten? I know of a pristine Bassman Ten, but am only interested in the chassis. It has the original quad of 32 ohm CTS speakers and is in remarkable condition. I have a cabinet for the chassis, so would buy it if I could find a taker for the cabinet.

        Reply
      • March 12, 2019 at 3:49 am
        Permalink

        Alan, I responded to an earlier post regarding your interest in acquiring a cabinet for a Bassman Ten. Please let me know if you are still looking. I found a complete amplifier in A+ condition. I only want the chassis. I am located in Florida. Where are you?

        Reply
  • May 15, 2018 at 6:15 pm
    Permalink

    Just had the mods on my 1978 Fender Bassman Ten completed! I gave it four Jensen 10″ Mod 10-30 speakers wired to 16 ohms. I had an amp tech go through and replace all of the tone caps to match that of the Fender Super Reverb specs. Replaced all of the tubes with 12AX7’s. Replaced all of the power caps. ( Quiet as brand new now!) Had the power tubes biased. My amp tech added a three way toggle switch it in the back that allows the amp to retain the stock Fender tone. Flip the switch another way, and you get a slightly overdriven blues tone. Silky smooth! Flip it the other way, and you’ll get a beautiful, rockin’ overdrive. This amp doesn’t start to wake up until the pre’s are dimed out, the channels jumpered, and the master is at 4-5. But at that volume in a house, your ears are going to bleed soon! A power attenuator is next on the shopping list! If you’re brave enough to play it at 6, you’ve got full on Marshall tone! He also added a new fuse, and new speaker plug, and a new power cable that was long overdue. And to think! Some kid thought he was ripping me off when he sold me the original amp with no speakers for just $60! $230 more in mods…and this thing is a tone monster! If you’re in the Indianapolis / Noblesville area, let me know, and I’ll send you his info.

    Reply
    • July 22, 2018 at 8:56 am
      Permalink

      Did you take it to Uncle Albert’s, or is there another good tube amp shop in Indy? I have a bassman ten and would love to have it gone through like that. Thanks!

      Reply
  • June 6, 2018 at 12:24 pm
    Permalink

    FYI.

    The 50 watt version (72-77) has the windings for a tube rectifier. Easy mod for any competent tech, so I had it done to mine.

    I absolutely adore this amp. I put Jensen MOD10-35 speakers in it and thought it was perfect. Gigged with it for years. I routinely got laughs or funny looks at lugging such a huge amp around but the tone and booming presence always shut everyone up. It’s one of the most underrated and overlooked vintage fender amps in history. For $4-500 you can STILL pick up a relatively clean one and have a GREAT amp.

    Anyway, I had a baby and got married and became a square. 6 years later I still missed the amp, so I tracked it down through the guy I sold it to and bought it back. It’s never leaving again. It’s right beside my 65 Tremolux as my 2 all time favorite amps.

    Reply
  • September 30, 2020 at 1:30 pm
    Permalink

    I have a 1977 Bassman 10 and it is the 50 watt version so, I think your 72-76 date should be extended to 77. Mine was originally purchased 7/77 and has a 1977 chassis serial number. Thanks

    Reply

Leave a Reply to Steven Prince Cancel reply

Your email address will not be published. Required fields are marked *